16. API - Boards and Accessories¶

These additional interfaces are provided to group collections of components together for ease of use, and as examples. They are composites made up of components from the various API - Input Devices and API - Output Devices provided by GPIO Zero. See those pages for more information on using components individually.

Note

All GPIO pin numbers use Broadcom (BCM) numbering by default. See the Pin Numbering section for more information.

16.1. Regular Classes¶

The following classes are intended for general use with the devices they are named after. All classes in this section are concrete (not abstract).

16.1.1. LEDBoard¶

class gpiozero.LEDBoard(*pins, pwm=False, active_high=True, initial_value=False, pin_factory=None, **named_pins)[source]¶

Extends LEDCollection and represents a generic LED board or collection of LEDs.

The following example turns on all the LEDs on a board containing 5 LEDs attached to GPIO pins 2 through 6:

from gpiozero import LEDBoard

leds = LEDBoard(2, 3, 4, 5, 6)
leds.on()

Parameters:

*pins – Specify the GPIO pins that the LEDs of the board are attached to. See Pin Numbering for valid pin numbers. You can designate as many pins as necessary. You can also specify LEDBoard instances to create trees of LEDs.
pwm (bool) – If True, construct PWMLED instances for each pin. If False (the default), construct regular LED instances.
active_high (bool) – If True (the default), the on() method will set all the associated pins to HIGH. If False, the on() method will set all pins to LOW (the off() method always does the opposite).
initial_value (bool or None) – If False (the default), all LEDs will be off initially. If None, each device will be left in whatever state the pin is found in when configured for output (warning: this can be on). If True, the device will be switched on initially.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).
**named_pins – Specify GPIO pins that LEDs of the board are attached to, associating each LED with a property name. You can designate as many pins as necessary and use any names, provided they’re not already in use by something else. You can also specify LEDBoard instances to create trees of LEDs.

blink(on_time=1, off_time=1, fade_in_time=0, fade_out_time=0, n=None, background=True)[source]¶

Make all the LEDs turn on and off repeatedly.

Parameters:

on_time (float) – Number of seconds on. Defaults to 1 second.
off_time (float) – Number of seconds off. Defaults to 1 second.
fade_in_time (float) – Number of seconds to spend fading in. Defaults to 0. Must be 0 if pwm was False when the class was constructed (ValueError will be raised if not).
fade_out_time (float) – Number of seconds to spend fading out. Defaults to 0. Must be 0 if pwm was False when the class was constructed (ValueError will be raised if not).
n (int or None) – Number of times to blink; None (the default) means forever.
background (bool) – If True, start a background thread to continue blinking and return immediately. If False, only return when the blink is finished (warning: the default value of n will result in this method never returning).

off(*args)[source]¶

If no arguments are specified, turn all the LEDs off. If arguments are specified, they must be the indexes of the LEDs you wish to turn off. For example:

from gpiozero import LEDBoard

leds = LEDBoard(2, 3, 4, 5)
leds.on()      # turn on all LEDs
leds.off(0)    # turn off the first LED (pin 2)
leds.off(-1)   # turn off the last LED (pin 5)
leds.off(1, 2) # turn off the middle LEDs (pins 3 and 4)
leds.on()      # turn on all LEDs

If blink() is currently active, it will be stopped first.

Parameters:	args (int) – The index(es) of the LED(s) to turn off. If no indexes are specified turn off all LEDs.

on(*args)[source]¶

If no arguments are specified, turn all the LEDs on. If arguments are specified, they must be the indexes of the LEDs you wish to turn on. For example:

from gpiozero import LEDBoard

leds = LEDBoard(2, 3, 4, 5)
leds.on(0)    # turn on the first LED (pin 2)
leds.on(-1)   # turn on the last LED (pin 5)
leds.on(1, 2) # turn on the middle LEDs (pins 3 and 4)
leds.off()    # turn off all LEDs
leds.on()     # turn on all LEDs

If blink() is currently active, it will be stopped first.

Parameters:	args (int) – The index(es) of the LED(s) to turn on. If no indexes are specified turn on all LEDs.

pulse(fade_in_time=1, fade_out_time=1, n=None, background=True)[source]¶

Make all LEDs fade in and out repeatedly. Note that this method will only work if the pwm parameter was True at construction time.

Parameters:

fade_in_time (float) – Number of seconds to spend fading in. Defaults to 1.
fade_out_time (float) – Number of seconds to spend fading out. Defaults to 1.
n (int or None) – Number of times to blink; None (the default) means forever.
background (bool) – If True (the default), start a background thread to continue blinking and return immediately. If False, only return when the blink is finished (warning: the default value of n will result in this method never returning).

toggle(*args)[source]¶

If no arguments are specified, toggle the state of all LEDs. If arguments are specified, they must be the indexes of the LEDs you wish to toggle. For example:

from gpiozero import LEDBoard

leds = LEDBoard(2, 3, 4, 5)
leds.toggle(0)   # turn on the first LED (pin 2)
leds.toggle(-1)  # turn on the last LED (pin 5)
leds.toggle()    # turn the first and last LED off, and the
                 # middle pair on

If blink() is currently active, it will be stopped first.

Parameters:	args (int) – The index(es) of the LED(s) to toggle. If no indexes are specified toggle the state of all LEDs.

16.1.2. LEDBarGraph¶

class gpiozero.LEDBarGraph(*pins, pwm=False, active_high=True, initial_value=0, pin_factory=None)[source]¶

Extends LEDCollection to control a line of LEDs representing a bar graph. Positive values (0 to 1) light the LEDs from first to last. Negative values (-1 to 0) light the LEDs from last to first.

The following example demonstrates turning on the first two and last two LEDs in a board containing five LEDs attached to GPIOs 2 through 6:

from gpiozero import LEDBarGraph
from time import sleep

graph = LEDBarGraph(2, 3, 4, 5, 6)
graph.value = 2/5  # Light the first two LEDs only
sleep(1)
graph.value = -2/5 # Light the last two LEDs only
sleep(1)
graph.off()

As with all other output devices, source and values are supported:

from gpiozero import LEDBarGraph, MCP3008
from signal import pause

graph = LEDBarGraph(2, 3, 4, 5, 6, pwm=True)
pot = MCP3008(channel=0)

graph.source = pot

pause()

Parameters:

*pins – Specify the GPIO pins that the LEDs of the bar graph are attached to. See Pin Numbering for valid pin numbers. You can designate as many pins as necessary.
pwm (bool) – If True, construct PWMLED instances for each pin. If False (the default), construct regular LED instances. This parameter can only be specified as a keyword parameter.
active_high (bool) – If True (the default), the on() method will set all the associated pins to HIGH. If False, the on() method will set all pins to LOW (the off() method always does the opposite). This parameter can only be specified as a keyword parameter.
initial_value (float) – The initial value of the graph given as a float between -1 and +1. Defaults to 0.0. This parameter can only be specified as a keyword parameter.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

lit_count¶: The number of LEDs on the bar graph actually lit up. Note that just like value, this can be negative if the LEDs are lit from last to first.

source¶: The iterable to use as a source of values for value.

value¶

The value of the LED bar graph. When no LEDs are lit, the value is 0. When all LEDs are lit, the value is 1. Values between 0 and 1 light LEDs linearly from first to last. Values between 0 and -1 light LEDs linearly from last to first.

To light a particular number of LEDs, simply divide that number by the number of LEDs. For example, if your graph contains 3 LEDs, the following will light the first:

from gpiozero import LEDBarGraph

graph = LEDBarGraph(12, 16, 19)
graph.value = 1/3

Note

Setting value to -1 will light all LEDs. However, querying it subsequently will return 1 as both representations are the same in hardware. The readable range of value is effectively -1 < value <= 1.

values¶: An infinite iterator of values read from value.

16.1.3. ButtonBoard¶

class gpiozero.ButtonBoard(*pins, pull_up=True, active_state=None, bounce_time=None, hold_time=1, hold_repeat=False, pin_factory=None, **named_pins)[source]¶

Extends CompositeDevice and represents a generic button board or collection of buttons. The value of the button board is a tuple of all the buttons states. This can be used to control all the LEDs in a LEDBoard with a ButtonBoard:

from gpiozero import LEDBoard, ButtonBoard
from signal import pause

leds = LEDBoard(2, 3, 4, 5)
btns = ButtonBoard(6, 7, 8, 9)
leds.source = btns.values
pause()

Alternatively you could represent the number of pressed buttons with an LEDBarGraph:

from gpiozero import LEDBarGraph, ButtonBoard
from signal import pause

graph = LEDBarGraph(2, 3, 4, 5)
btns = ButtonBoard(6, 7, 8, 9)
graph.source = (sum(value) for value in btn.values)
pause()

Parameters:

*pins – Specify the GPIO pins that the buttons of the board are attached to. See Pin Numbering for valid pin numbers. You can designate as many pins as necessary.
pull_up (bool or None) – If True (the default), the GPIO pins will be pulled high by default. In this case, connect the other side of the buttons to ground. If False, the GPIO pins will be pulled low by default. In this case, connect the other side of the buttons to 3V3. If None, the pin will be floating, so it must be externally pulled up or down and the active_state parameter must be set accordingly.
active_state (bool or None) – See description under InputDevice for more information.
bounce_time (float) – If None (the default), no software bounce compensation will be performed. Otherwise, this is the length of time (in seconds) that the buttons will ignore changes in state after an initial change.
hold_time (float) – The length of time (in seconds) to wait after any button is pushed, until executing the when_held handler. Defaults to 1.
hold_repeat (bool) – If True, the when_held handler will be repeatedly executed as long as any buttons remain held, every hold_time seconds. If False (the default) the when_held handler will be only be executed once per hold.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).
**named_pins – Specify GPIO pins that buttons of the board are attached to, associating each button with a property name. You can designate as many pins as necessary and use any names, provided they’re not already in use by something else.

wait_for_press(timeout=None)¶

Pause the script until the device is activated, or the timeout is reached.

Parameters:	timeout (float or None) – Number of seconds to wait before proceeding. If this is `None` (the default), then wait indefinitely until the device is active.

wait_for_release(timeout=None)¶

Pause the script until the device is deactivated, or the timeout is reached.

Parameters:	timeout (float or None) – Number of seconds to wait before proceeding. If this is `None` (the default), then wait indefinitely until the device is inactive.

is_pressed¶: Composite devices are considered “active” if any of their constituent devices have a “truthy” value.

pressed_time¶: The length of time (in seconds) that the device has been active for. When the device is inactive, this is None.

value¶: A namedtuple() containing a value for each subordinate device. Devices with names will be represented as named elements. Unnamed devices will have a unique name generated for them, and they will appear in the position they appeared in the constructor.

when_pressed¶

The function to run when the device changes state from inactive to active.

This can be set to a function which accepts no (mandatory) parameters, or a Python function which accepts a single mandatory parameter (with as many optional parameters as you like). If the function accepts a single mandatory parameter, the device that activated will be passed as that parameter.

Set this property to None (the default) to disable the event.

when_released¶

The function to run when the device changes state from active to inactive.

This can be set to a function which accepts no (mandatory) parameters, or a Python function which accepts a single mandatory parameter (with as many optional parameters as you like). If the function accepts a single mandatory parameter, the device that deactivated will be passed as that parameter.

Set this property to None (the default) to disable the event.

16.1.4. TrafficLights¶

class gpiozero.TrafficLights(red, amber, green, *, yellow=None, pwm=False, initial_value=False, pin_factory=None)[source]¶

Extends LEDBoard for devices containing red, yellow, and green LEDs.

The following example initializes a device connected to GPIO pins 2, 3, and 4, then lights the amber (yellow) LED attached to GPIO 3:

from gpiozero import TrafficLights

traffic = TrafficLights(2, 3, 4)
traffic.amber.on()

Parameters:

red (int or str) – The GPIO pin that the red LED is attached to. See Pin Numbering for valid pin numbers.
amber (int or str or None) – The GPIO pin that the amber LED is attached to. See Pin Numbering for valid pin numbers.
yellow (int or str or None) – The GPIO pin that the yellow LED is attached to. This is merely an alias for the amber parameter; you can’t specify both amber and yellow. See Pin Numbering for valid pin numbers.
green (int or str) – The GPIO pin that the green LED is attached to. See Pin Numbering for valid pin numbers.
pwm (bool) – If True, construct PWMLED instances to represent each LED. If False (the default), construct regular LED instances.
initial_value (bool or None) – If False (the default), all LEDs will be off initially. If None, each device will be left in whatever state the pin is found in when configured for output (warning: this can be on). If True, the device will be switched on initially.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

red¶: The red LED or PWMLED.

amber¶: The amber LED or PWMLED. Note that this attribute will not be present when the instance is constructed with the yellow keyword parameter.

yellow¶: The yellow LED or PWMLED. Note that this attribute will only be present when the instance is constructed with the yellow keyword parameter.

green¶: The green LED or PWMLED.

16.1.5. TrafficLightsBuzzer¶

class gpiozero.TrafficLightsBuzzer(lights, buzzer, button, *, pin_factory=None)[source]¶

Extends CompositeOutputDevice and is a generic class for HATs with traffic lights, a button and a buzzer.

Parameters:

lights (TrafficLights) – An instance of TrafficLights representing the traffic lights of the HAT.
buzzer (Buzzer) – An instance of Buzzer representing the buzzer on the HAT.
button (Button) – An instance of Button representing the button on the HAT.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

lights¶: The TrafficLights instance passed as the lights parameter.

buzzer¶: The Buzzer instance passed as the buzzer parameter.

button¶: The Button instance passed as the button parameter.

16.1.6. PiHutXmasTree¶

class gpiozero.PiHutXmasTree(*, pwm=False, initial_value=False, pin_factory=None)[source]¶

Extends LEDBoard for The Pi Hut’s Xmas board: a 3D Christmas tree board with 24 red LEDs and a white LED as a star on top.

The 24 red LEDs can be accessed through the attributes led0, led1, led2, and so on. The white star LED is accessed through the star attribute. Alternatively, as with all descendents of LEDBoard, you can treat the instance as a sequence of LEDs (the first element is the star).

The Xmas Tree board pins are fixed and therefore there’s no need to specify them when constructing this class. The following example turns all the LEDs on one at a time:

from gpiozero import PiHutXmasTree
from time import sleep

tree = PiHutXmasTree()

for light in tree:
    light.on()
    sleep(1)

The following example turns the star LED on and sets all the red LEDs to flicker randomly:

from gpiozero import PiHutXmasTree
from gpiozero.tools import random_values
from signal import pause

tree = PiHutXmasTree(pwm=True)

tree.star.on()

for led in tree[1:]:
    led.source_delay = 0.1
    led.source = random_values()

pause()

Parameters:

pwm (bool) – If True, construct PWMLED instances for each pin. If False (the default), construct regular LED instances.
initial_value (bool or None) – If False (the default), all LEDs will be off initially. If None, each device will be left in whatever state the pin is found in when configured for output (warning: this can be on). If True, the device will be switched on initially.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

star¶: Returns the LED or PWMLED representing the white star on top of the tree.

led0, led1, led2, ...: Returns the LED or PWMLED representing one of the red LEDs. There are actually 24 of these properties named led0, led1, and so on but for the sake of brevity we represent all 24 under this section.

16.1.7. LedBorg¶

class gpiozero.LedBorg(*, pwm=True, initial_value=(0, 0, 0), pin_factory=None)[source]¶

Extends RGBLED for the PiBorg LedBorg: an add-on board containing a very bright RGB LED.

The LedBorg pins are fixed and therefore there’s no need to specify them when constructing this class. The following example turns the LedBorg purple:

from gpiozero import LedBorg

led = LedBorg()
led.color = (1, 0, 1)

Parameters:

initial_value (Color or tuple) – The initial color for the LedBorg. Defaults to black (0, 0, 0).
pwm (bool) – If True (the default), construct PWMLED instances for each component of the LedBorg. If False, construct regular LED instances, which prevents smooth color graduations.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.8. PiLiter¶

class gpiozero.PiLiter(*, pwm=False, initial_value=False, pin_factory=None)[source]¶

Extends LEDBoard for the Ciseco Pi-LITEr: a strip of 8 very bright LEDs.

The Pi-LITEr pins are fixed and therefore there’s no need to specify them when constructing this class. The following example turns on all the LEDs of the Pi-LITEr:

from gpiozero import PiLiter

lite = PiLiter()
lite.on()

Parameters:

pwm (bool) – If True, construct PWMLED instances for each pin. If False (the default), construct regular LED instances.
initial_value (bool or None) – If False (the default), all LEDs will be off initially. If None, each LED will be left in whatever state the pin is found in when configured for output (warning: this can be on). If True, the each LED will be switched on initially.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.9. PiLiterBarGraph¶

class gpiozero.PiLiterBarGraph(*, pwm=False, initial_value=False, pin_factory=None)[source]¶

Extends LEDBarGraph to treat the Ciseco Pi-LITEr as an 8-segment bar graph.

The Pi-LITEr pins are fixed and therefore there’s no need to specify them when constructing this class. The following example sets the graph value to 0.5:

from gpiozero import PiLiterBarGraph

graph = PiLiterBarGraph()
graph.value = 0.5

Parameters:	pwm (bool) – If `True`, construct `PWMLED` instances for each pin. If `False` (the default), construct regular `LED` instances. initial_value (float) – The initial `value` of the graph given as a float between -1 and +1. Defaults to `0.0`. pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.10. PiTraffic¶

class gpiozero.PiTraffic(*, pwm=False, initial_value=False, pin_factory=None)[source]¶

Extends TrafficLights for the Low Voltage Labs PI-TRAFFIC vertical traffic lights board when attached to GPIO pins 9, 10, and 11.

There’s no need to specify the pins if the PI-TRAFFIC is connected to the default pins (9, 10, 11). The following example turns on the amber LED on the PI-TRAFFIC:

from gpiozero import PiTraffic

traffic = PiTraffic()
traffic.amber.on()

To use the PI-TRAFFIC board when attached to a non-standard set of pins, simply use the parent class, TrafficLights.

Parameters:

pwm (bool) – If True, construct PWMLED instances to represent each LED. If False (the default), construct regular LED instances.
initial_value (bool) – If False (the default), all LEDs will be off initially. If None, each device will be left in whatever state the pin is found in when configured for output (warning: this can be on). If True, the device will be switched on initially.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.11. PiStop¶

class gpiozero.PiStop(location, *, pwm=False, initial_value=False, pin_factory=None)[source]¶

Extends TrafficLights for the PiHardware Pi-Stop: a vertical traffic lights board.

The following example turns on the amber LED on a Pi-Stop connected to location A+:

from gpiozero import PiStop

traffic = PiStop('A+')
traffic.amber.on()

Parameters:

location (str) – The location on the GPIO header to which the Pi-Stop is connected. Must be one of: A, A+, B, B+, C, D.
pwm (bool) – If True, construct PWMLED instances to represent each LED. If False (the default), construct regular LED instances.
initial_value (bool) – If False (the default), all LEDs will be off initially. If None, each device will be left in whatever state the pin is found in when configured for output (warning: this can be on). If True, the device will be switched on initially.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.12. FishDish¶

class gpiozero.FishDish(*, pwm=False, pin_factory=None)[source]¶

Extends TrafficLightsBuzzer for the Pi Supply FishDish: traffic light LEDs, a button and a buzzer.

The FishDish pins are fixed and therefore there’s no need to specify them when constructing this class. The following example waits for the button to be pressed on the FishDish, then turns on all the LEDs:

from gpiozero import FishDish

fish = FishDish()
fish.button.wait_for_press()
fish.lights.on()

Parameters:	pwm (bool) – If `True`, construct `PWMLED` instances to represent each LED. If `False` (the default), construct regular `LED` instances. pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.13. TrafficHat¶

class gpiozero.TrafficHat(*, pwm=False, pin_factory=None)[source]¶

Extends TrafficLightsBuzzer for the Ryanteck Traffic HAT: traffic light LEDs, a button and a buzzer.

The Traffic HAT pins are fixed and therefore there’s no need to specify them when constructing this class. The following example waits for the button to be pressed on the Traffic HAT, then turns on all the LEDs:

from gpiozero import TrafficHat

hat = TrafficHat()
hat.button.wait_for_press()
hat.lights.on()

Parameters:	pwm (bool) – If `True`, construct `PWMLED` instances to represent each LED. If `False` (the default), construct regular `LED` instances. pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.14. JamHat¶

class gpiozero.JamHat(*, pwm=False, pin_factory=None)[source]¶

Extends CompositeOutputDevice for the ModMyPi JamHat board.

There are 6 LEDs, two buttons and a tonal buzzer. The pins are fixed. Usage:

from gpiozero import JamHat

hat = JamHat()

hat.button_1.wait_for_press()
hat.lights_1.on()
hat.buzzer.play('C4')
hat.button_2.wait_for_press()
hat.off()

Parameters:	pwm (bool) – If `True`, construct :class: PWMLED instances to represent each LED on the board. If `False` (the default), construct regular `LED` instances. pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

lights_1, lights_2

Two LEDBoard instances representing the top (lights_1) and bottom (lights_2) rows of LEDs on the JamHat.

red, yellow, green: LED or PWMLED instances representing the red, yellow, and green LEDs along the top row.

button_1, button_2: The left (button_1) and right (button_2) Button objects on the JamHat.

buzzer¶: The Buzzer at the bottom right of the JamHat.

off()[source]¶: Turns all the LEDs off and stops the buzzer.

on()[source]¶: Turns all the LEDs on and makes the buzzer play its mid tone.

16.1.15. Robot¶

class gpiozero.Robot(left, right, *, pwm=True, pin_factory=None)[source]¶

Extends CompositeDevice to represent a generic dual-motor robot.

This class is constructed with two tuples representing the forward and backward pins of the left and right controllers respectively. For example, if the left motor’s controller is connected to GPIOs 4 and 14, while the right motor’s controller is connected to GPIOs 17 and 18 then the following example will drive the robot forward:

from gpiozero import Robot

robot = Robot(left=(4, 14), right=(17, 18))
robot.forward()

Parameters:

left (tuple) – A tuple of two (or three) GPIO pins representing the forward and backward inputs of the left motor’s controller. Use three pins if your motor controller requires an enable pin.
right (tuple) – A tuple of two (or three) GPIO pins representing the forward and backward inputs of the right motor’s controller. Use three pins if your motor controller requires an enable pin.
pwm (bool) – If True (the default), construct PWMOutputDevice instances for the motor controller pins, allowing both direction and variable speed control. If False, construct DigitalOutputDevice instances, allowing only direction control.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

left_motor¶: The Motor on the left of the robot.

right_motor¶: The Motor on the right of the robot.

backward(speed=1, **kwargs)[source]¶

Drive the robot backward by running both motors backward.

Parameters:

speed (float) – Speed at which to drive the motors, as a value between 0 (stopped) and 1 (full speed). The default is 1.
curve_left (float) – The amount to curve left while moving backwards, by driving the left motor at a slower speed. Maximum curve_left is 1, the default is 0 (no curve). This parameter can only be specified as a keyword parameter, and is mutually exclusive with curve_right.
curve_right (float) – The amount to curve right while moving backwards, by driving the right motor at a slower speed. Maximum curve_right is 1, the default is 0 (no curve). This parameter can only be specified as a keyword parameter, and is mutually exclusive with curve_left.

forward(speed=1, **kwargs)[source]¶

Drive the robot forward by running both motors forward.

Parameters:

speed (float) – Speed at which to drive the motors, as a value between 0 (stopped) and 1 (full speed). The default is 1.
curve_left (float) – The amount to curve left while moving forwards, by driving the left motor at a slower speed. Maximum curve_left is 1, the default is 0 (no curve). This parameter can only be specified as a keyword parameter, and is mutually exclusive with curve_right.
curve_right (float) – The amount to curve right while moving forwards, by driving the right motor at a slower speed. Maximum curve_right is 1, the default is 0 (no curve). This parameter can only be specified as a keyword parameter, and is mutually exclusive with curve_left.

left(speed=1)[source]¶

Make the robot turn left by running the right motor forward and left motor backward.

Parameters:	speed (float) – Speed at which to drive the motors, as a value between 0 (stopped) and 1 (full speed). The default is 1.

reverse()[source]¶: Reverse the robot’s current motor directions. If the robot is currently running full speed forward, it will run full speed backward. If the robot is turning left at half-speed, it will turn right at half-speed. If the robot is currently stopped it will remain stopped.

right(speed=1)[source]¶

Make the robot turn right by running the left motor forward and right motor backward.

Parameters:	speed (float) – Speed at which to drive the motors, as a value between 0 (stopped) and 1 (full speed). The default is 1.

stop()[source]¶: Stop the robot.

value¶: Represents the motion of the robot as a tuple of (left_motor_speed, right_motor_speed) with (-1, -1) representing full speed backwards, (1, 1) representing full speed forwards, and (0, 0) representing stopped.

16.1.16. PhaseEnableRobot¶

class gpiozero.PhaseEnableRobot(left, right, *, pwm=True, pin_factory=None)[source]¶

Extends CompositeDevice to represent a dual-motor robot based around a Phase/Enable motor board.

This class is constructed with two tuples representing the phase (direction) and enable (speed) pins of the left and right controllers respectively. For example, if the left motor’s controller is connected to GPIOs 12 and 5, while the right motor’s controller is connected to GPIOs 13 and 6 so the following example will drive the robot forward:

from gpiozero import PhaseEnableRobot

robot = PhaseEnableRobot(left=(5, 12), right=(6, 13))
robot.forward()

Parameters:

left (tuple) – A tuple of two GPIO pins representing the phase and enable inputs of the left motor’s controller.
right (tuple) – A tuple of two GPIO pins representing the phase and enable inputs of the right motor’s controller.
pwm (bool) – If True (the default), construct PWMOutputDevice instances for the motor controller’s enable pins, allowing both direction and variable speed control. If False, construct DigitalOutputDevice instances, allowing only direction control.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

left_motor¶: The PhaseEnableMotor on the left of the robot.

right_motor¶: The PhaseEnableMotor on the right of the robot.

backward(speed=1)[source]¶

Drive the robot backward by running both motors backward.

Parameters:	speed (float) – Speed at which to drive the motors, as a value between 0 (stopped) and 1 (full speed). The default is 1.

forward(speed=1)[source]¶

Drive the robot forward by running both motors forward.

Parameters:	speed (float) – Speed at which to drive the motors, as a value between 0 (stopped) and 1 (full speed). The default is 1.

left(speed=1)[source]¶

Make the robot turn left by running the right motor forward and left motor backward.

Parameters:	speed (float) – Speed at which to drive the motors, as a value between 0 (stopped) and 1 (full speed). The default is 1.

reverse()[source]¶: Reverse the robot’s current motor directions. If the robot is currently running full speed forward, it will run full speed backward. If the robot is turning left at half-speed, it will turn right at half-speed. If the robot is currently stopped it will remain stopped.

right(speed=1)[source]¶

Make the robot turn right by running the left motor forward and right motor backward.

Parameters:	speed (float) – Speed at which to drive the motors, as a value between 0 (stopped) and 1 (full speed). The default is 1.

stop()[source]¶: Stop the robot.

value¶: Returns a tuple of two floating point values (-1 to 1) representing the speeds of the robot’s two motors (left and right). This property can also be set to alter the speed of both motors.

16.1.17. RyanteckRobot¶

class gpiozero.RyanteckRobot(*, pwm=True, pin_factory=None)[source]¶

Extends Robot for the Ryanteck motor controller board.

The Ryanteck MCB pins are fixed and therefore there’s no need to specify them when constructing this class. The following example drives the robot forward:

from gpiozero import RyanteckRobot

robot = RyanteckRobot()
robot.forward()

Parameters:	pwm (bool) – If `True` (the default), construct `PWMOutputDevice` instances for the motor controller pins, allowing both direction and variable speed control. If `False`, construct `DigitalOutputDevice` instances, allowing only direction control. pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.18. CamJamKitRobot¶

class gpiozero.CamJamKitRobot(*, pwm=True, pin_factory=None)[source]¶

Extends Robot for the CamJam #3 EduKit motor controller board.

The CamJam robot controller pins are fixed and therefore there’s no need to specify them when constructing this class. The following example drives the robot forward:

from gpiozero import CamJamKitRobot

robot = CamJamKitRobot()
robot.forward()

Parameters:	pwm (bool) – If `True` (the default), construct `PWMOutputDevice` instances for the motor controller pins, allowing both direction and variable speed control. If `False`, construct `DigitalOutputDevice` instances, allowing only direction control. pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.19. PololuDRV8835Robot¶

class gpiozero.PololuDRV8835Robot(*, pwm=True, pin_factory=None)[source]¶

Extends PhaseEnableRobot for the Pololu DRV8835 Dual Motor Driver Kit.

The Pololu DRV8835 pins are fixed and therefore there’s no need to specify them when constructing this class. The following example drives the robot forward:

from gpiozero import PololuDRV8835Robot

robot = PololuDRV8835Robot()
robot.forward()

Parameters:

pwm (bool) – If True (the default), construct PWMOutputDevice instances for the motor controller’s enable pins, allowing both direction and variable speed control. If False, construct DigitalOutputDevice instances, allowing only direction control.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

16.1.20. Energenie¶

class gpiozero.Energenie(socket, *, initial_value=False, pin_factory=None)[source]¶

Extends Device to represent an Energenie socket controller.

This class is constructed with a socket number and an optional initial state (defaults to False, meaning off). Instances of this class can be used to switch peripherals on and off. For example:

from gpiozero import Energenie

lamp = Energenie(1)
lamp.on()

Parameters:

socket (int) – Which socket this instance should control. This is an integer number between 1 and 4.
initial_value (bool) – The initial state of the socket. As Energenie sockets provide no means of reading their state, you must provide an initial state for the socket, which will be set upon construction. This defaults to False which will switch the socket off.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

off()[source]¶: Turns the socket off.

on()[source]¶: Turns the socket on.

socket¶: Returns the socket number.

value¶: Returns True if the socket is on and False if the socket is off. Setting this property changes the state of the socket.

16.1.21. StatusZero¶

class gpiozero.StatusZero(*labels, pwm=False, active_high=True, initial_value=False, pin_factory=None)[source]¶

Extends LEDBoard for The Pi Hut’s STATUS Zero: a Pi Zero sized add-on board with three sets of red/green LEDs to provide a status indicator.

The following example designates the first strip the label “wifi” and the second “raining”, and turns them green and red respectfully:

from gpiozero import StatusZero

status = StatusZero('wifi', 'raining')
status.wifi.green.on()
status.raining.red.on()

Each designated label will contain two LED objects named “red” and “green”.

Parameters:

*labels (str) – Specify the names of the labels you wish to designate the strips to. You can list up to three labels. If no labels are given, three strips will be initialised with names ‘one’, ‘two’, and ‘three’. If some, but not all strips are given labels, any remaining strips will not be initialised.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

your-label-here, your-label-here, ...

This entry represents one of the three labelled attributes supported on the STATUS Zero board. It is an LEDBoard which contains:

red¶: The LED or PWMLED representing the red LED next to the label.

green¶: The LED or PWMLED representing the green LED next to the label.

16.1.22. StatusBoard¶

class gpiozero.StatusBoard(*labels, pwm=False, active_high=True, initial_value=False, pin_factory=None)[source]¶

Extends CompositeOutputDevice for The Pi Hut’s STATUS board: a HAT sized add-on board with five sets of red/green LEDs and buttons to provide a status indicator with additional input.

The following example designates the first strip the label “wifi” and the second “raining”, turns the wifi green and then activates the button to toggle its lights when pressed:

from gpiozero import StatusBoard

status = StatusBoard('wifi', 'raining')
status.wifi.lights.green.on()
status.wifi.button.when_pressed = status.wifi.lights.toggle

Each designated label will contain a “lights” LEDBoard containing two LED objects named “red” and “green”, and a Button object named “button”.

Parameters:

*labels (str) – Specify the names of the labels you wish to designate the strips to. You can list up to five labels. If no labels are given, five strips will be initialised with names ‘one’ to ‘five’. If some, but not all strips are given labels, any remaining strips will not be initialised.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

your-label-here, your-label-here, ...

This entry represents one of the five labelled attributes supported on the STATUS board. It is an CompositeOutputDevice which contains:

lights¶

A LEDBoard representing the lights next to the label. It contains:

red¶: The LED or PWMLED representing the red LED next to the label.

green¶: The LED or PWMLED representing the green LED next to the label.

button¶: A Button representing the button next to the label.

16.1.23. SnowPi¶

class gpiozero.SnowPi(*, pwm=False, initial_value=False, pin_factory=None)[source]¶

Extends LEDBoard for the Ryanteck SnowPi board.

The SnowPi pins are fixed and therefore there’s no need to specify them when constructing this class. The following example turns on the eyes, sets the nose pulsing, and the arms blinking:

from gpiozero import SnowPi

snowman = SnowPi(pwm=True)
snowman.eyes.on()
snowman.nose.pulse()
snowman.arms.blink()

Parameters:

pwm (bool) – If True, construct PWMLED instances to represent each LED. If False (the default), construct regular LED instances.
initial_value (bool) – If False (the default), all LEDs will be off initially. If None, each device will be left in whatever state the pin is found in when configured for output (warning: this can be on). If True, the device will be switched on initially.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

arms¶

A LEDBoard representing the arms of the snow man. It contains the following attributes:

left, right

Two LEDBoard objects representing the left and right arms of the snow-man. They contain:

top, middle, bottom: The LED or PWMLED down the snow-man’s arms.

eyes¶

A LEDBoard representing the eyes of the snow-man. It contains:

left, right: The LED or PWMLED for the snow-man’s eyes.

nose¶: The LED or PWMLED for the snow-man’s nose.

16.1.24. PumpkinPi¶

class gpiozero.PumpkinPi(*, pwm=False, initial_value=False, pin_factory=None)[source]¶

Extends LEDBoard for the ModMyPi PumpkinPi board.

There are twelve LEDs connected up to individual pins, so for the PumpkinPi the pins are fixed. For example:

from gpiozero import PumpkinPi

pumpkin = PumpkinPi(pwm=True)
pumpkin.sides.pulse()
pumpkin.off()

Parameters:

pwm (bool) – If True, construct PWMLED instances to represent each LED. If False (the default), construct regular LED instances
initial_value (bool or None) – If False (the default), all LEDs will be off initially. If None, each device will be left in whatever state the pin is found in when configured for output (warning: this can be on). If True, the device will be switched on initially.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).

sides¶

A LEDBoard representing the LEDs around the edge of the pumpkin. It contains:

left, right

Two LEDBoard instances representing the LEDs on the left and right sides of the pumpkin. They each contain:

top, midtop, middle, midbottom, bottom: Each LED or PWMLED around the specified side of the pumpkin.

eyes¶

A LEDBoard representing the eyes of the pumpkin. It contains:

left, right: The LED or PWMLED for each of the pumpkin’s eyes.

16.2. Base Classes¶

The classes in the sections above are derived from a series of base classes, some of which are effectively abstract. The classes form the (partial) hierarchy displayed in the graph below:

For composite devices, the following chart shows which devices are composed of which other devices:

The following sections document these base classes for advanced users that wish to construct classes for their own devices.

16.2.1. LEDCollection¶

class gpiozero.LEDCollection(*pins, pwm=False, active_high=True, initial_value=False, pin_factory=None, **named_pins)[source]¶

Extends CompositeOutputDevice. Abstract base class for LEDBoard and LEDBarGraph.

leds¶: A flat tuple of all LEDs contained in this collection (and all sub-collections).

16.2.2. CompositeOutputDevice¶

class gpiozero.CompositeOutputDevice(*args, _order=None, pin_factory=None, **kwargs)[source]¶

Extends CompositeDevice with on(), off(), and toggle() methods for controlling subordinate output devices. Also extends value to be writeable.

Parameters:

*args (Device) – The un-named devices that belong to the composite device. The value attributes of these devices will be represented within the composite device’s tuple value in the order specified here.
_order (list or None) – If specified, this is the order of named items specified by keyword arguments (to ensure that the value tuple is constructed with a specific order). All keyword arguments must be included in the collection. If omitted, an alphabetically sorted order will be selected for keyword arguments.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).
**kwargs (Device) – The named devices that belong to the composite device. These devices will be accessible as named attributes on the resulting device, and their value attributes will be accessible as named elements of the composite device’s tuple value.

off()[source]¶: Turn all the output devices off.

on()[source]¶: Turn all the output devices on.

toggle()[source]¶: Toggle all the output devices. For each device, if it’s on, turn it off; if it’s off, turn it on.

value¶: A tuple containing a value for each subordinate device. This property can also be set to update the state of all subordinate output devices.

16.2.3. CompositeDevice¶

class gpiozero.CompositeDevice(*args, _order=None, pin_factory=None, **kwargs)[source]¶

Extends Device. Represents a device composed of multiple devices like simple HATs, H-bridge motor controllers, robots composed of multiple motors, etc.

The constructor accepts subordinate devices as positional or keyword arguments. Positional arguments form unnamed devices accessed by treating the composite device as a container, while keyword arguments are added to the device as named (read-only) attributes.

For example:

>>> from gpiozero import *
>>> d = CompositeDevice(LED(2), LED(3), LED(4), btn=Button(17))
>>> d[0]
<gpiozero.LED object on pin GPIO2, active_high=True, is_active=False>
>>> d[1]
<gpiozero.LED object on pin GPIO3, active_high=True, is_active=False>
>>> d[2]
<gpiozero.LED object on pin GPIO4, active_high=True, is_active=False>
>>> d.btn
<gpiozero.Button object on pin GPIO17, pull_up=True, is_active=False>
>>> d.value
CompositeDeviceValue(device_0=False, device_1=False, device_2=False, btn=False)

Parameters:

*args (Device) – The un-named devices that belong to the composite device. The value attributes of these devices will be represented within the composite device’s tuple value in the order specified here.
_order (list or None) – If specified, this is the order of named items specified by keyword arguments (to ensure that the value tuple is constructed with a specific order). All keyword arguments must be included in the collection. If omitted, an alphabetically sorted order will be selected for keyword arguments.
pin_factory (Factory or None) – See API - Pins for more information (this is an advanced feature which most users can ignore).
**kwargs (Device) – The named devices that belong to the composite device. These devices will be accessible as named attributes on the resulting device, and their value attributes will be accessible as named elements of the composite device’s tuple value.

close()[source]¶

Shut down the device and release all associated resources. This method can be called on an already closed device without raising an exception.

This method is primarily intended for interactive use at the command line. It disables the device and releases its pin(s) for use by another device.

You can attempt to do this simply by deleting an object, but unless you’ve cleaned up all references to the object this may not work (even if you’ve cleaned up all references, there’s still no guarantee the garbage collector will actually delete the object at that point). By contrast, the close method provides a means of ensuring that the object is shut down.

For example, if you have a breadboard with a buzzer connected to pin 16, but then wish to attach an LED instead:

>>> from gpiozero import *
>>> bz = Buzzer(16)
>>> bz.on()
>>> bz.off()
>>> bz.close()
>>> led = LED(16)
>>> led.blink()

Device descendents can also be used as context managers using the with statement. For example:

>>> from gpiozero import *
>>> with Buzzer(16) as bz:
...     bz.on()
...
>>> with LED(16) as led:
...     led.on()
...

is_active¶: Composite devices are considered “active” if any of their constituent devices have a “truthy” value.

namedtuple¶: The namedtuple() type constructed to represent the value of the composite device. The value attribute returns values of this type.

value¶: A namedtuple() containing a value for each subordinate device. Devices with names will be represented as named elements. Unnamed devices will have a unique name generated for them, and they will appear in the position they appeared in the constructor.

16. API - Boards and Accessories¶

16.1. Regular Classes¶

16.1.1. LEDBoard¶

16.1.2. LEDBarGraph¶

16.1.3. ButtonBoard¶

16.1.4. TrafficLights¶

16.1.5. TrafficLightsBuzzer¶

16.1.6. PiHutXmasTree¶

16.1.7. LedBorg¶

16.1.8. PiLiter¶

16.1.9. PiLiterBarGraph¶

16.1.10. PiTraffic¶

16.1.11. PiStop¶

16.1.12. FishDish¶

16.1.13. TrafficHat¶

16.1.14. JamHat¶

16.1.15. Robot¶

16.1.16. PhaseEnableRobot¶

16.1.17. RyanteckRobot¶

16.1.18. CamJamKitRobot¶

16.1.19. PololuDRV8835Robot¶

16.1.20. Energenie¶

16.1.21. StatusZero¶

16.1.22. StatusBoard¶

16.1.23. SnowPi¶

16.1.24. PumpkinPi¶

16.2. Base Classes¶

16.2.1. LEDCollection¶

16.2.2. CompositeOutputDevice¶

16.2.3. CompositeDevice¶

Table Of Contents

Previous topic

Next topic

This Page